Aircraft maintenance checks

From Wikipedia, the free encyclopedia
Jump to navigation Jump to search
A United States Navy SH-60F Seahawk helicopter undergoing routine maintenance in 2005

Aircraft maintenance checks are periodic inspections that have to be done on all commercial/civil aircraft after a certain amount of time or usage; military aircraft normally follow specific maintenance programmes which may or may not be similar to those of commercial/civil operators. Airlines and other commercial operators of large or turbine-powered aircraft follow a continuous inspection program approved by the Federal Aviation Administration (FAA) in the United States,[1] or by other airworthiness authorities such as Transport Canada or the European Aviation Safety Agency (EASA). Each operator prepares a Continuous Airworthiness Maintenance Program (CAMP) under its Operations Specifications or "OpSpecs".[2] The CAMP includes both routine and detailed inspections.

Airlines and airworthiness authorities casually refer to the detailed inspections as "checks", commonly one of the following: A check, B check, C check, or D check. A and B checks are lighter checks, while C and D are considered heavier checks. Aircraft operators may perform some work at their own facilities but often checks, and especially the heavier checks, take place at maintenance, repair and overhaul (MRO) company sites.[3]

A check[edit]

This is performed approximately every 400-600 flight hours or 200–300 cycles (takeoff and landing is considered an aircraft "cycle"), depending on aircraft type.[4] It needs about 50-70 man-hours and is usually on the ground in a hangar for a minimum of 10 hours. The actual occurrence of this check varies by aircraft type, the cycle count, or the number of hours flown since the last check. The occurrence can be delayed by the airline if certain predetermined conditions are met.

B check[edit]

This is performed approximately every 6-8 months. It needs about 160-180 man-hours, depending on the aircraft, and is usually completed within 1–3 days at an airport hangar. A similar occurrence schedule applies to the B check as to the A check. However, B checks are increasingly incorporated into successive A checks, i.e.: Checks A-1 through A-10 complete all the B check items.[5]

C check[edit]

This is performed approximately every 20–24 months or a specific number of actual flight hours (FH) or as defined by the manufacturer. This maintenance check is much more extensive than a B check, requiring a large majority of the aircraft's components to be inspected. This check puts the aircraft out of service, and the aircraft must not leave the maintenance site until it is completed. It also requires more space than A and B checks. It is, therefore, usually carried out in a hangar at a maintenance base. The time needed to complete such a check is at least 1–2 weeks and the effort involved can require up to 6,000 man-hours.

3C check[edit]

Some authorities use a type of check, known as a 3C check or Intermediate Layover (IL), which typically includes light structural maintenance, including checks for corrosion, or on specific high-load parts of the airframe.[6] It may also be used as the opportunity for cabin upgrades (for example, new seats, entertainment systems, carpeting) which would otherwise put the aircraft out of service for a significant time without the need for an inspection. As component reliability has improved, some MROs now spread the workload across several C checks, or incorporate this 3C check into D checks instead.[7]

D check[edit]

The D check, sometimes known as a "heavy maintenance visit" (HMV)[8] is by far the most comprehensive and demanding check for an airplane. This check occurs approximately every 6-10 years.[7] It is a check that more or less takes the entire airplane apart for inspection and overhaul. Even the paint may need to be completely removed for further inspection on the fuselage metal skin. Such a check can generally take up to 50,000 man-hours and 2 months to complete, depending on the aircraft and the number of technicians involved.[9] It also requires the most space of all maintenance checks, and as such must be performed at a suitable maintenance base. The requirements and the tremendous effort involved in this maintenance check make it by far the most expensive, with total costs for a single D check in the million-dollar range.[10]

Because of the nature and the cost of such a check, most airlines — especially those with a large fleet — have to plan D checks for their aircraft years in advance. Often, older aircraft being phased out of a particular airline's fleet are either stored or scrapped upon reaching their next D check, due to the high costs involved in comparison to the aircraft's value.[11] On average, a commercial aircraft undergoes two or three D checks before being retired.[12]

Maintenance Review Board (US)[edit]

In the United States, initial aircraft maintenance requirements are proposed in a Maintenance Review Board (MRB) report[13] based on Air Transport Association (ATA) publication MSG-3 (Maintenance Steering Group – 3rd Task Force).

Modern transport category airplanes with MSG-3-derived maintenance programs employ usage parameters for each maintenance requirement such as flight hours, calendar time, or flight cycles. Maintenance intervals based on usage parameters allow more flexibility in scheduling the maintenance program to optimize aircraft utilization and minimize aircraft downtime.

References[edit]

  1. ^ AFS-600 (2008). "Chapter 8. Inspection Fundamentals" (PDF). Aviation Maintenance Technician Handbook (pdf). Federal Aviation Administration. pp. 8–15. FAA-H-8083-30. Retrieved 2014-12-01. 
  2. ^ AFS (2009). "Vol. 3 Chapters 18 & 43". Flight Standards Information Management System. CHG 80. Federal Aviation Administration. Order 8900.1. Retrieved 2010-01-12. 
  3. ^ "UK Aerospace Maintenance, Repair, Overhaul & Logistics Industry Analysis" (PDF). UK Government Department for Business, Innovation & Skills. p. 16. Retrieved 14 December 2017. 
  4. ^ Kinnison, Harry; Siddiqui, Tariq (2011). Aviation Maintenance Management (2 ed.). McGraw-Hill. p. 122. ISBN 978-0-07-180502-5. 
  5. ^ "The A, C and D of aircraft maintenance". Qantas. 
  6. ^ "Major maintenance due for A380s". MRO Network. Retrieved 14 December 2017. 
  7. ^ a b "Aircraft maintenance at Lufthansa Technik". Lufthansa Technik. Retrieved 14 December 2017. 
  8. ^ "Glossary of aircraft maintenance terms and abbreviations". Monarch Engineering. Retrieved 14 December 2017. 
  9. ^ "Overhaul". Lufthansa Technik. Retrieved 14 December 2017. 
  10. ^ Fabozzi, Frank, ed. (2000). Investing in asset-backed securities. New Hope, PA: Frank J. Fabozzi Associates. p. 156. ISBN 1883249805. Retrieved 14 December 2017. 
  11. ^ "The Relationship between an Aircraft's Value and its Maintenance Status" (PDF). Aircraft Monitor. Retrieved 14 December 2017. 
  12. ^ Scheinberg, Ronald (2017). The Commercial Aircraft Finance Handbook. Routledge. ISBN 1351364219. Retrieved 5 August 2018. 
  13. ^ AFS-330 (1997). Maintenance Review Board Procedures (pdf). Federal Aviation Administration. Advisory Circular AC 121-22A. Retrieved 2010-01-12. 

External links[edit]